Search results

Have an 881 to sell. Bought the saw new a couple of years ago. Ran somewhere between 5 to 8 tanks through it. Thinking $1650 shipped.

Have a few loops of 26rs to sell. They are new chains spun off a roll. PRICES ARE PER LOOP SHIPPED 16"- 62DL- 3639 005 0062 QTY 2 $14 18"- 68DL- 3639 005 0068 QTY 1 $15 18"- 74DL- 3639 005 0074 QTY 1 $16

Have a used redlight carb box. Has light and wiring harness. Have no idea if light works. Its not cracked or broken, but does have some scuffs and scrapes. Lip where carb grommet goes is folded in and cracked. See last pic. Comes with attaching screws. Thinking $20 shipped. Open to offers.

Have a lightly used maxflow kit for ms660. Comes with all the pieces. New white and green filters. $40 shipped. If price is out of line let me know.

I have a Stihl 024AV and a Echo CS-750EVL up for sale. Would like to get $200 a piece shipped. Here is the thread on the 750 from a few years back. https://opeforum.com/threads/echo-cs-750evl.22652/ Have not run the saw since I set the tune.Went threw the 024 as well. Fuel lines, carb kit, new...

Can or does any know the differences in the service tool AS part number 5910 007 2222 and the older 5910 007 2205. There must have been some design changes but i cant find tech bulletin on it. @jacob j.

Not sure if this is the right place for this. Have had the idea of doing a chain filing class for a few years. To share some of the knowledge i have with others. Looking for some insight on what some of you would look for, or what should be covered. Explaining the parts of the chain its self...

On the hunt for a 500i W. The W is for heated handles. Or for the parts to make a regular 500i in one with heated handles. Here is a list of the parts 1147 430 0513 Switch 1121 442 0402 Insulating Hose Qty2 1147 790 1701 Handlebar 1110 430 0202 Stop Switch 0000 958 1511 Washer 1128 432 2200...

Has anyone found a good way to reattach the heating element in the rear handle. It has a stickie backing when new. I feel once pulled off. Its not going to stick any more.

Have a friend looking for a 660. New or near new would be best. But open to other overall condition. $1300 is the budget. But let me know what you got if you are thinking more.

Does any know if any manufacturer makes a D025/3003 mount bar that is 3/8 lo pro/ picco 16" .050 gauge. Have a 024 that i would like to run 63ps chain on. Not apposed to modding the tail on a 3005 bar but would like it to be factory

Looking for part number 1124 442 0400 Insulating hose. It goes over the short circuit and ground wire. It also fits a few heated handle bar saws. Where the wires come out of the handlebar. 084, 038, 036, 064, MS360, MS361, MS361C, 034, MS660, 088, 066 Any help would be greatly appreciated. Have...

I would like to know why Nate@fordf150 got banned today.

I am working on my echo PB 8010. It has a walbro WYAB 1 carb. Is the low speed adjustment screw up top down threw the throttle shaft? And the high speed on the side near the fuel inlet nipple? Maybe i got it backwards. I know they are both the small d.

Looking for some recommendations on a builder for a 390 or 395. Have a friend that is going to buy either a new 390 or 395.

Looking for a nos carb grommet. Part number 1124 123 7500

So I am going to get my 084 powder coated by Mike. While tearing the saw down I found this mark on the exhaust skirt. Trying to figure out what is going on. It doesn't look like transfer to me. I should say this cylinder was reused from when i got the saw. Someone put a new piston and cylinder...

Can some here tell or explain the difference in Crankshafts for the 346xp. Looks like they made a change to them when they went to the new edition. The old edition part number is 503857671. The new edition part number is 504206802. Looks to me that they used the 503857571 crank until 08 in the...

Just picked these up today. I have always wanted to be able to pressure and vac test a saws after a case split and not have to put the tank handle back on. Guess someone at stihl had the same idea. The manifold is from a 660. 880/088/084 is not not going to work with this.

I am looking for a 346xpg or 2153cwh. It does not have to be perfect. Not afraid of a builder saw either. Just has to have an intact heating system and handle bar.