Search results

Hi folks, looking for an IPL for a PM Canadien 340/Skil 1631 saw. Can anyone help me out? Thanks in advance for the help!

Does anyone have the IPL for a Homelite 900 D? Any assistance would be greatly appreciated. Thanks!

Looking for a usable Super Pro 81 cylinder and piston. Does anyone have anything they would be willing to part with? I haven’t had any luck looking in the usual places, so I thought I would post here. I have found piston kits, but unfortunately, no cylinders. Please let me know and thanks in...

Folks, I’ve got a weird one. MS250, looks like low hours b/c I have 135 psi compression and p/c look like new (as seen through intake and exhaust ports). Saw was run for unknown amount of time without air filter. Couldn’t have been long (I assume) given there is no visible damage to...

Does anyone have a clutch/bar cover that will fit a Homelite 1050? FedEx decide to break mine in shipping. Let me know, thanks!

I finally got around to putting together my 066 kit from Huztl. I bought this about 3 months after they started selling full kits so I guess I got an early one. I decided to go with OEM gaskets, seals, oil and gas caps, intake and impulse line and sprung for the AM big bore kit. I used the...

I bought a bunch of new and used parts off a gentleman 9+ months ago. The picture was kinda crappy but there were a few things in the lot that I needed for projects. I was busy with other things and getting ready to move so when the box showed up, I opened it, confirmed there were parts in the...

Looking for a builder saw, prefer complete, bad cylinder ok. Anyone got one they would sell? LMK

Hi guys, one of my best friends just hook me up with an awesome saw. It appears that it is a Lombard tempest 651 but I’m struggling to find any information about it on the net. Does anybody have any info they can point me to on this saw? And yes, it runs!

Does anyone have a set of bar guide plates for an Olympyk 272? Let me know, thanks!

After getting my new Homelite EZ automatic today I realized I’ve become addicted to small saws. Between it, my Powr Kraft 2.8, my Stihl 015 and my Olympyk 935DL i’m digging on all these little rippers. I have a newer Mac 35cc but it’s not the same. I like the straight stack, high reving noise...

Looking for good lower shrouds to fit the 051, 075, 076 models. PN 1111 080 1600 or 4205 080 1600. Need 3

I recently bought several old NOS McCulloch bars, PN 65273 and 65274. They are marked as “Slimline” bars, 24” and 28” long. The pattern is correct to fit the Mac 660 I have but it is the wrong gage (measures .062”, too small for a .404 chain?). On the 660 the studs are .365” (9.24mm) in...

Could someone who has a Pioneer 650 take a picture of the throttle linkage and post it? Mine is missing and I'm thinking I'll have to just make my own. Anyone who could help me? Thanks!

The Huztl 070 kit popped up today in my email. Anyone pulled the trigger on one of these yet? Tempting....

I know if you have a saw with a burnt piston you should run a pressure check to make sure the seals are still good but what other symptoms would also lead you to run a pressure check?

Looking for PM Canadien saws; 270, 275, 360, 370, etc.. Any for sale out there? Let me know. Thanks!

Guys, I need some help here. Fresh rebuild, only 1/2 tank through the saw and the owner tells me it crashes. Upon disassembly I find both clutch and flywheel nuts loose and key is sheared. I tear it all the way down and find some strange damage on the inner bearing surface of the rod journal...

Hi guys, need help with an old Bantam. It has a weird recoil system that grabs the clutch nut to spin over the motor instead of the normal pawl and cup setup. Trying to find an IPL that shows this setup so that I can try to find the parts that I need. I need the big nut, the spacer behind it...

What causes a saw to run hot? I know if the mixture is too lean you can burn it up but I have never seen this kind of a condition that I found in this 048. It looks like the piston underside got really hot and the skirt failed. Would bad seals cause something like this to happen? This saw...