Search results

Does anyone know any obvious differences between these 2 cylinders? I am trying to figure out what would be the best one to start a hybrid build but not finding a lot of what the differences are. If someone has both laying around or has dealt with both and could let me know what you may have...

Looking for a few 9000 or 9010 parts Makita models would work too. Need air box and carb mount, top covers, brake handle and clutch cover to name a few.

Anyone have any of the big cylinders laying around for some bolt spacing measurements I am planning a potential hybrid mission but need some info on where to start on a cylinder. I am thinking if anyone has 084, 088, 3120, or even an 066 or 395 cylinder laying around those would be my first...

Looking for a dolmar 7900 crank with a bad rod bearing for a science project. Let me know what you got

I have a brainstorm going on for a cheap stroker crank. If there is enough material could you offset grind the pin hole and use a bigger bearing and pin and then press it all back together? Would going a mm or 2 bigger make the crank too far out of balance? Taking any thoughts and input thanks

Does anyone have a 034 crank out that could give me a rough length of the connecting rod from center of big end pin to center of small end pin? Thanks in advance

Got a couple quick questions about the carb on the 2260. I inherited this saw a while back and it used to be used by my dad logging so been used... Anyway cleaned it up and fixed the primer and got it running but it doesn't start or idle great and sounds like the auto tune is just way off. I ran...

Has anyone ever compared a Makita dpc7300 cutoff saw cylinder to a ps7300 chainsaw cylinder? Obvious difference in plug angle and it doesn't have the side mount but if those were corrected think port timing and everything would be the same?

Anyone know where to find specs for different tillotson HS carburetors? Trying to figure out some differences in models.

Looking for a recoil, muffler and top cover for a r440. I believe most of the parts are the same as p100. Let me know what you may have thanks in advance.

I have this old partner I believe is a r440 it was painted blue at one point but originally appears to be mostly yellow. Has a decomp 56mm bore. Anyway it is missing a muffler, top cover, and recoil and I am going to try to get it running again. Can someone help me here is the serial number

Does anyone have junk Zama c3m kicking around that has a good throttle and choke shaft? I have carb off my 7900 that started giving issues and found the throttle shaft is very worn. Body of carb still seems good so was hoping to get it back in service. Let me know what you have and price. Thanks...

Got this 120si finished up and would like to pass this classic dolmar on to a new home. Has a good cylinder and piston, new bearings, seals, rings, brake band and I am probably forgetting some stuff too. Added a side outlet like the 6800s had and welded all the way around because these were...

I picked this 9000 up about a month or so ago. I saw it for sale and couldn't pass it up but I haven't used it since I got it and could really use the money for other bills. I got it running replaced a few mounts and gave it a few revs that's all. Had the muffler off piston looks super clean has...

Looking for a set of 120si 6800 series bar studs and need 2 inner bar plates too. Let me know if you have anything you want to part with. Thanks

Brought this 394xp back to life from a part saw. Saw runs and oils good these things really oil. It has new dukes piston, aftermarket top covers, clutch cover and handle. Jacobj hooked me up with a nice used crank and has new snr bearings new seals and case gasket. Only issues I know of are has...

Got more saws than trees left at this point and could use funds for other house projects. Saw has new bearings and seals I did some porting on the cylinder new ring i am impressed with how strong it is. Oils really good muffler is gutted and has 272 unlimited coil. Really hate to sell this one...

Got this little 490 and just doesn't fit in on the dolmar wall. Any interest in it out there? Runs well only ran one tank through it since getting it. Switched it to .325 to put this bar on it.

Anyone know when dolmar changed the 120 super, 120si, 6800 49mm cylinder. I noticed tonight that some have the tab to support the rings on the intake and others don't. Anyone have any idea what cylinder makes more power or if it matters?

Looking for a top cover and recoil for a jonsered 2260 and a tank for 562 or 2260 have a 562 I want to use the 2260 style top cover on. Anyone got anything?