Echo rear handle 2511 - CS-2511WES

Dub11 · Nov 10, 2019

chipper1 said:
Anyone run one with the 3/8 picco chain.
Not asking about it on a top handle, I've heard all the complaints, as well as the others.
Thanks.

Picco?

I wanna run full 3/8s on a ported on of these! I want to avoid another chain flavor in the mix.

RI Chevy · Nov 10, 2019

Why doesn't anyone use .325?

Dub11 · Nov 10, 2019

RI Chevy said:
Why doesn't anyone use .325?

Good point a .325kn would be pretty sweet.

usmcbuckwild · Nov 10, 2019

Dub11 said:
Good point a .325kn would be pretty sweet.

While these are snotty little bastards when ported, I don’t think they have enough ass to run larger chain. After running one with 1/4” i think they should have come stock with 1/4. Remember; they are only 25 cc and are rpm limited. I think if they were unlimited they might get the chain speed up more, but don’t think they make enough torque to keep it going.

For anyone who ran the 2511T I did at the CT GTG, it was able to keep the chain going while the bar was buried in a log. The entire bar, including the nose. But that was asking a-lot from the little ported saw. And that was a chain that had been sharpened with much less hook than stock so it wasn’t grabbing as much as oem.

Dub11 · Nov 10, 2019

usmcbuckwild said:
While these are snotty little bastards when ported, I don’t think they have enough ass to run larger chain. After running one with 1/4” i think they should have come stock with 1/4. Remember; they are only 25 cc and are rpm limited. I think if they were unlimited they might get the chain speed up more, but don’t think they make enough torque to keep it going.

For anyone who ran the 2511T I did at the CT GTG, it was able to keep the chain going while the bar was buried in a log. The entire bar, including the nose. But that was asking a-lot from the little ported saw. And that was a chain that had been sharpened with much less hook than stock so it wasn’t grabbing as much as oem.

Have you seen that one @Nutball did pulling 20" 3/8s?

In all reality by the time I get one the internet will have figured out the perfect b/c combo for me.

chipper1 · Nov 10, 2019

Dub11 said:
Picco?

I wanna run full 3/8s on a ported on of these! I want to avoid another chain flavor in the mix.

Yep, run it on a good number of saws as well as my pole saw so it wouldn't be adding anything, but that's why I don't want to do the 1/4", lot's of files and guides already

.

Dub11 said:
Have you seen that one @Nutball did pulling 20" 3/8s?

In all reality by the time I get one the internet will have figured out the perfect b/c combo for me.

Ran a buddies ported 200 rear handle with a 20x3/8, it had no problem with it

. I'm sure you could do it with a 355, but the 2511 would be asking a lot for day to day work.
I have a 2511t, now I need the rear handle version

.

Dub11 · Nov 10, 2019

chipper1 said:
Yep, run it on a good number of saws as well as my pole saw so it wouldn't be adding anything, but that's why I don't want to do the 1/4", lot's of files and guides already .

Ran a buddies ported 200 rear handle with a 20x3/8, it had no problem with it . I'm sure you could do it with a 355, but the 2511 would be asking a lot for day to day work.
I have a 2511t, now I need the rear handle version .

Oh I'd never ask it to pull it at all but since its been done, it just tells me that it could pull some lowly. 325nk easily.

What bar mount does the 2511 use?

usmcbuckwild · Nov 10, 2019

Dub11 said:
Have you seen that one @Nutball did pulling 20" 3/8s?

In all reality by the time I get one the internet will have figured out the perfect b/c combo for me.

where the hell is THAT thread?!?!? I want to see that

Dub11 · Nov 10, 2019

usmcbuckwild said:
where the hell is THAT thread?!?!? I want to see that

Not sure what thread this made it too but here's the vijao

USMC615 · Nov 10, 2019

Dub11 said:
Not sure what thread this made it too but here's the vijao

Bad ass little saw...

00wyk · Nov 10, 2019

Problem running 3/8LP like VXL on the 2511 is the tiny saw feels very jittery unless you grind off the heels of the top plate. But it works fine with Stihl picco. Also the kick back can be more sudden.

usmcbuckwild · Nov 10, 2019

Dub11 said:
Not sure what thread this made it too but here's the vijao

huh. I’m gonna have to try that

Nutball · Nov 10, 2019

usmcbuckwild said:
huh. I’m gonna have to try that

Geico might have to sponsor my video of MORE! you know those "more" commercials

and the other so you can watch both at the same time

BTW they'll crank up a good 4 stroking 14,500-16000rpm if done right, no limiter I know of.

Fairways_and_Greens · Nov 10, 2019

RI Chevy said:
Why doesn't anyone use .325?

Would that work with a dime tip?

RI Chevy · Nov 10, 2019

??? Not sure

00wyk · Nov 11, 2019

I dunno, either. But I do know that 325 is a bit tight on my quarter tip.

RI Chevy · Nov 11, 2019

What chain do you run on that bar?

00wyk · Nov 11, 2019

RI Chevy said:
What chain do you run on that bar?

I'm running 325. It's much shorter links than 3/8LP/Picco, and less kickey backey when carving with it. I'll get a pic when I get back home. I have another one with fresh chain on it so it's easy to see.

RI Chevy · Nov 11, 2019

Nice...

chipper1 · Nov 11, 2019

Dub11 said:
Oh I'd never ask it to pull it at all but since its been done, it just tells me that it could pull some lowly. 325nk easily.

What bar mount does the 2511 use?

Could, but why, I like picco chain a lot on the little saws and if the 2511 doesn't have a problem with running it and smoothly, then I'll be running it.

00wyk said:
Problem running 3/8LP like VXL on the 2511 is the tiny saw feels very jittery unless you grind off the heels of the top plate. But it works fine with Stihl picco. Also the kick back can be more sudden.

That's funny, I see what you did there, kickback

.
I can do heals with this, or another grinder manually.

Echo rear handle 2511 - CS-2511WES

Saw R skeery

Mastermind Approved!

Saw R skeery

Buck

Saw R skeery

Here For The Long Haul!

Saw R skeery

Buck

Saw R skeery

Fapper Fi

Here For The Long Haul!

Buck

Here For The Long Haul!

Super OPE Member

Mastermind Approved!

Here For The Long Haul!

Mastermind Approved!

Here For The Long Haul!

Mastermind Approved!

Here For The Long Haul!

Similar threads