What's on your bench?

huskyboy · Jul 5, 2019

Fuel, compression and ignition need those three things.

usmcbuckwild · Jul 5, 2019

Tpagel said:
I did this and it will hit until mix gone from cylinder.

Stupid question, but did you ensure it is getting impulse signal?

brandonstclair20 · Jul 5, 2019

I finished this up today. Yikes efco parts are hard to get!

Sent from my iPhone using Tapatalk

huskyboy · Jul 5, 2019

brandonstclair20 said:
I finished this up today. Yikes efco parts are hard to get!

Sent from my iPhone using Tapatalk

Watch your shirt tail near that flywheel

. How many cc is it?

NCFarmboy · Jul 5, 2019

Looks like a 181 to me. If it is 81cc dual port cyl.
Shep

Tpagel · Jul 5, 2019

Homelite SD50, Echo 610evl, 3900

brandonstclair20 · Jul 5, 2019

huskyboy said:
Watch your shirt tail near that flywheel . How many cc is it?

Efco 181, 81cc

Sent from my iPhone using Tapatalk

merc_man · Jul 6, 2019

Tpagel said:
Homelite SD50, Echo 610evl, 3900

Sweet 610. I would love to get one someday.

Sent from my SM-G950W using Tapatalk

drf256 · Jul 6, 2019

Finally had a few hours to play with a saw again. This is an 046 D jug that’s going on a buddy’s 440.

usmcbuckwild · Jul 6, 2019

drf256 said:
Finally had a few hours to play with a saw again. This is an 046 D jug that’s going on a buddy’s 440.

View attachment 189425 View attachment 189426 View attachment 189427 View attachment 189428 View attachment 189429

Great work Doc. Why aren’t you asleep?

Cut4fun · Jul 6, 2019

brandonstclair20 said:
I finished this up today. Yikes efco parts are hard to get!

Sent from my iPhone using Tapatalk

Did Chad get you those oem circlips you needed or is the others in there?

Cut4fun · Jul 6, 2019

huskyboy said:
Watch your shirt tail near that flywheel . How many cc is it?

I cut and put me some of those back in recoil to have for use one time. 2 part plastic epoxy and cut some plastic from a mantis donor.

Recoil before fixing 12-2013.

Cut4fun · Jul 6, 2019

Looking back in old thread 2013.

Cut these.

Recoil after fixing to use.

brandonstclair20 · Jul 6, 2019

Cut4fun said:
Did Chad get you those oem circlips you needed or is the others in there?

They haven’t been ordered yet. Since I had everything else I am going to give it a go. I have the right clips for the piston that’s on the saw.

Sent from my iPhone using Tapatalk

brandonstclair20 · Jul 6, 2019

Cut4fun said:
Looking back in old thread 2013.

Cut these. View attachment 189468 Recoil after fixing to use.
View attachment 189471

Good idea!

Sent from my iPhone using Tapatalk

Stump Shot · Jul 6, 2019

huskyboy said:
Fuel, compression and ignition need those three things.

...and exhaust. Gotta have that too!

Stump Shot · Jul 6, 2019

drf256 said:
Finally had a few hours to play with a saw again. This is an 046 D jug that’s going on a buddy’s 440.

View attachment 189425 View attachment 189426 View attachment 189427 View attachment 189428 View attachment 189429

Do you like the D's better than the circular chambered ones?

huskyboy · Jul 6, 2019

Stump Shot said:
...and exhaust. Gotta have that too!

Good point! Can’t forget bad clogged spark screens lol

Czed · Jul 6, 2019

Czed · Jul 6, 2019

Pissy little .105 line doesn't last a few minutes
So i modified my 230srm to 1.55 line
Ran a whole tank through it never bump fed it once.

What's on your bench?

Sorta a husqvarna guy...

Buck

Pinnacle OPE Member

Sorta a husqvarna guy...

Pinnacle OPE Member

Pinnacle OPE Member

Pinnacle OPE Member

merc_man

Dr. Richard Cranium

Buck

Redneck Chainsaw Repair

Redneck Chainsaw Repair

Redneck Chainsaw Repair

Pinnacle OPE Member

Pinnacle OPE Member

Disciple of Monkey's

Disciple of Monkey's

Sorta a husqvarna guy...

Aluminium Member

Aluminium Member

Similar threads