I know it's just a 064

MG porting · Jun 8, 2019

Time's Standing Stihl said:
I like me some 064s

Sounds good you guys are making me want to go cut some trees down!!

Time's Standing Stihl · Jun 8, 2019

MG porting said:
Sounds good you guys are making me want to go cut some trees down!!

See if i can help you out more. Sold this one last year

MG porting · Jun 8, 2019

Time's Standing Stihl said:
See if i can help you out more. Sold this one last year

Lol. Now you're just teasing.

RI Chevy · Jun 8, 2019

Uber clean looking saw there!

huskyboy · Jun 9, 2019

MG porting said:
Cool I wish I had that cylinder b

Wish I had one of those instead of two of the same cylinders like this lol but at least I have a spare if I need it.View attachment 185228

Are the KS better than mahle? I wish I took pics of the ports so we could compare them.

MG porting · Jun 9, 2019

huskyboy said:
Are the KS better than mahle? I wish I took pics of the ports so we could compare them.

Some say they are but I think with port work to both I don't think it would make much difference I just wanted one of each just so I could back up what I just said. Lol.

trooney · Jun 9, 2019

huskyboy said:
Are the KS better than mahle? I wish I took pics of the ports so we could compare them.

From what I understand Mason the KS had a little bit better numbers. They both are good cylinders though.

drf256 · Jun 10, 2019

I’ve never held a Mahle 064 jug in my hands. Every single one has been KS that I have seen.

MG porting · Jun 10, 2019

drf256 said:
I’ve never held a Mahle 064 jug in my hands. Every single one has been KS that I have seen.

Same same but they are out there just sneaking around.lol

BuckthornBonnie · Jun 10, 2019

Got a Mahle on one of mine. Runs fine... good saw.

huskyboy · Jun 10, 2019

Does this mean my saw is a unicorn? Should I advance it past the whole key and grind through the transfers? Could be a top 3 strongest saw. Lol

trooney · Jun 10, 2019

huskyboy said:
Does this mean my saw is a unicorn? Should I advance it past the whole key and grind through the transfers? Could be a top 3 strongest saw.

Yes....

huskyboy · Jun 10, 2019

trooney said:
Yes....

I’ll sell you the cylinder for 300 bucks.

RI Chevy · Jun 10, 2019

Nah...It's good enough for who its for.

MG porting · Jun 10, 2019

huskyboy said:
I’ll sell you the cylinder for 300 bucks.

I'll sell mine to you for $300.

the cylinder.lol

rogue60 · Jun 10, 2019

huskyboy said:
Yes them too and 660’s. I’m convinced it has to be the flywheel. What else could it be?

It's definitely the flywheel on this family of saws. I used to like the sound you knew you had a good chain/tune when they whistle/whine.

Hinerman · Jun 11, 2019

huskyboy said:
I’ll sell you the cylinder for 300 bucks.

I'll rebuild it from damaged parts and belt sand the cylinder for $1500...

huskyboy · Jun 11, 2019

Hinerman said:
I'll rebuild it from damaged parts and belt sand the cylinder for $1500...

I’ll be sold if you send me a video of it cutting one cookie cut with .050 off the rakers.

MustangMike · Jun 11, 2019

We should get back on topic before this gets named the remember JMS thread!

I'd prefer not to think about him.

deye223 · Jun 11, 2019

huskyboy said:
I’ll be sold if you send me a video of it cutting one cookie cut with .050 off the rakers.

Which is about where they should be with a half worn cutter ...... maybe even 0.60

I know it's just a 064

Pinnacle OPE Member

Below me...

Pinnacle OPE Member

Mastermind Approved!

Sorta a husqvarna guy...

Pinnacle OPE Member

Admitted Woodaholic

Dr. Richard Cranium

Pinnacle OPE Member

Pinnacle OPE Member

Sorta a husqvarna guy...

Admitted Woodaholic

Sorta a husqvarna guy...

Mastermind Approved!

Pinnacle OPE Member

Here For The Long Haul!

Mastermind Approved!

Sorta a husqvarna guy...

Mastermind Approved!

AIR FUEL SPARK VROOOOOM

Similar threads