Saw video thread

RI Chevy · Jan 26, 2020

It certainly runs nice and strong...[emoji106]
Nice job...
I try to remember to wear PPE most always when cutting. Sometimes I forget to bring, sometimes I bring and forget to put on...[emoji3061]
I cut my leg some years back. Was very lucky. 50 stiches. Missed my knee... Really woke me up

Bigmac · Jan 26, 2020

390xp, did some minor mods, bgd widended the ports and did a 288 deflector for the second port

huskihl · Jan 27, 2020

@cornykid

huskihl · Jan 27, 2020

Got a few of these to do so I got a vid of a 365 xtorq with just the transfer covers ground out. So it’s basically a 372 xtorq with a low top

Canadian farm boy · Jan 27, 2020

Ported MS260 arctic. Tuned fat for break in. New rings, crank seals etc.

WillG · Jan 27, 2020

My 034 after repair. Cutting video tomorrow.

Sent from my E6910 using Tapatalk

WillG · Jan 28, 2020

034 making a couple cuts after work

Sent from my E6910 using Tapatalk

RI Chevy · Jan 28, 2020

Nice Will.

WillG · Jan 28, 2020

RI Chevy said:
Nice Will.

Thank you buddy! I think it just needs a minor tweak on the low side. I'm going to get video of the 346 with dual port muffler tomorrow.

Sent from my E6910 using Tapatalk

ferris · Jan 29, 2020

WillG said:
034 making a couple cuts after work

Sent from my E6910 using Tapatalk

Big 1122 hardwood spikes?
Imho a little bit too big

WillG · Jan 29, 2020

ferris said:
Big 1122 hardwood spikes?
Imho a little bit too big

Ya they're a bit big. I have the original one which I'll put back on at some point.

Sent from my E6910 using Tapatalk

sawmikaze · Jan 29, 2020

WillG said:
Ya they're a bit big. I have the original one which I'll put back on at some point.

Sent from my E6910 using Tapatalk

Buy these.

ferris · Jan 29, 2020

@sawmikaze
Year that are the right dogs for 261 362 saws maybe 462 also

sawmikaze · Jan 29, 2020

ferris said:
@sawmikaze
Year that are the right dogs for 261 362 saws maybe 462 also

Not the 462.

26 and 36 series. And the 034.

WillG · Jan 29, 2020

@sawmikaze can you post a better pic of the bag with part number?

Sent from my E6910 using Tapatalk

WillG · Jan 29, 2020

Made some cuts with my 346XP conversion after work. Love this little saw! She's a screamer!

Sent from my E6910 using Tapatalk

sawmikaze · Jan 29, 2020

WillG said:
@sawmikaze can you post a better pic of the bag with part number?

Sent from my E6910 using Tapatalk

WillG · Jan 29, 2020

sawmikaze said:
View attachment 220982

Thank you

Sent from my E6910 using Tapatalk

DND 9000 · Jan 30, 2020

ferris said:
@sawmikaze
Year that are the right dogs for 261 362 saws maybe 462 also

This 0000 660 0800 set is used on the following: MS 260, 261, 341, 360, 361, 362, 400
Consists of bumber spike 1142 664 0500 (inner) and 1141 664 0501 (outer),
screw (2*) 9008 345 0960 and nut (2*) 9214 320 0700

WillG · Jan 30, 2020

Test cuts with the Super XL /XL-12. Did excellent. Just need to tweak the idle speed and mix a tad.

Sent from my E6910 using Tapatalk

Saw video thread

Mastermind Approved!

Mastermind Approved!

Muh fingers look really big

Muh fingers look really big

“Normal” people scare me.

Here For The Long Haul!

Here For The Long Haul!

Mastermind Approved!

Here For The Long Haul!

Pinnacle OPE Member

Here For The Long Haul!

Mastermind Approved!

Pinnacle OPE Member

Mastermind Approved!

Here For The Long Haul!

Here For The Long Haul!

Mastermind Approved!

Here For The Long Haul!

Pinnacle OPE Member

Here For The Long Haul!

Similar threads