Saw video thread

Wolverine · Jan 23, 2020

huskyboy said:
A big 40+” pine on the hillside we are logging. It was struck by lightning and was deteriorating pretty quickly by the looks of it. Some sketchy pines on this job for sure.

Nice 2-fer on that one.

Mkinslow · Jan 24, 2020

Husqvarna 55 I posted about in what's on your bench

Sent from my SM-G892A using Tapatalk

Agent Smith · Jan 24, 2020

Mkinslow said:
Husqvarna 55 I posted about in what's on your bench

Sent from my SM-G892A using Tapatalk

I picked up one of those today actually. Cant wait to tear it apart

Mkinslow · Jan 24, 2020

Agent Smith said:
I picked up one of those today actually. Cant wait to tear it apart

I like it,super simple to work on, in these cuts it had the 3/8 7tooth rim sprocket, I'm gonna swap it over to a 325 just because that's what all my other small saws are. It pulled it decently though.

Sent from my SM-G892A using Tapatalk

huskihl · Jan 24, 2020

Stupid hard sugar maple with grain going every which way. It was throwing noodles through part of it lol. New Archer off the roll seemed to leave a bit on the table. I went in and checked afterward and the rakers were at .022”. But it didn’t seem to stretch.
First cuts on new saw
@Cat 525

WillG · Jan 24, 2020

Sears 758G gear drive. Mid 60s, 20" bar and 1/2" pitch chain.

Sent from my E6910 using Tapatalk

JT78 · Jan 24, 2020

Couple videos of an old 55 closed port running some .325 I put together a few years back.

Duane(Pa) · Jan 25, 2020

JT78 said:
Couple videos of an old 55 closed port running some .325 I put together a few years back.

Good timing. Guess what’s sitting on my bench with a toasted top end? Getting a Meteor that I picked up from HL

Duane(Pa) · Jan 25, 2020

huskihl said:
Stupid hard sugar maple with grain going every which way. It was throwing noodles through part of it lol. New Archer off the roll seemed to leave a bit on the table. I went in and checked afterward and the rakers were at .022”. But it didn’t seem to stretch.
First cuts on new saw
@Cat 525

Looks nice there Kev & Tim! Would that be 562 iffin it was orange? Pardon my ignorance

TreeLife · Jan 25, 2020

Duane(Pa) said:
Looks nice there Kev & Tim! Would that be 562 iffin it was orange? Pardon my ignorance

Correct. It's a small mount 562 in black and red.

huskihl · Jan 25, 2020

Duane(Pa) said:
Looks nice there Kev & Tim! Would that be 562 iffin it was orange? Pardon my ignorance

It would actually be a 560, which isn’t available in the states. But like Dom said, small mount version of a 562

00wyk · Jan 25, 2020

A very stupidly hard piece of oak. We shoulda saved it for sumfin useful like a mantle. I used it to punish a few little saws.

Echo 360WES muffler mod
Makita 4300 ported
Stihl MS241 ported
Stihl 044 ported
Husqvarna 288XP muffler mod mostly(slightly ported sorta)
All out of the box factory chains.

Duane(Pa) · Jan 25, 2020

00wyk said:
A very stupidly hard piece of oak. We shoulda saved it for sumfin useful like a mantle. I used it to punish a few little saws.

Echo 360WES muffler mod
Makita 4300 ported
Stihl MS241 ported
Stihl 044 ported
Husqvarna 288XP muffler mod mostly(slightly ported sorta)
All out of the box factory chains.

Looks like the big dog shat all over the pups...

JT78 · Jan 25, 2020

Well got to play today broke out the 395 for some big oak.

RI Chevy · Jan 25, 2020

Where's all your PPE Gear Justin? Lol
Saw looked good. [emoji106]

00wyk · Jan 25, 2020

Duane(Pa) said:
Looks like the big dog shat all over the pups...

That 288 is running an 8 pin rim, with cleaned up ports and super gutted muffler, is lower RPM in the wood than the 044, but it is pulling like a freaking freight train the whole time with 32 inches of semi chisel. The 044 is running 84dl full chisel and a 7 pin ported using popular #s from here. The 4300 Makita/421 DOlmar has mini finger ports sprouting from the primaries and port work. It seems to keep it competitive with the ported 241(which is running 325 full kerf on 16- the Makita is running Picco on a 15). That 241 has partially compromised stratos, too. It's a strong saw for 42cc's. It feels a bit stronger than the 4300 i the wood, but that 4300 is on it's first tank!

JT78 · Jan 25, 2020

one more vid

JT78 · Jan 25, 2020

RI Chevy said:
Where's all your PPE Gear Justin? Lol
Saw looked good. [emoji106]

What's PPE? LOL!

RI Chevy · Jan 25, 2020

Lol. Funny til needed.
Tell us about the saw. Nice.

JT78 · Jan 26, 2020

RI Chevy said:
Lol. Funny til needed.
Tell us about the saw. Nice.

I pray I never need it!
The saw is a 395 that I bought and ported 10 years ago nothing super crazy, I never even checked the port timing on it. Just dropped the base gasket, widened the exhaust to about .030 of the sides of the Piston skirt and raised the exhaust the thickness of the gasket about .016. It has been run some but not abused it's still blowing 200lbs of compression. I generally only break it out for the Halifax county Heritage festival or when I run into something really big like this oak. Bar is a 42 running skip and an 8 pin sprocket.

Saw video thread

dilligaf

Here For The Long Haul!

Hack of all trades

Here For The Long Haul!

Muh fingers look really big

Here For The Long Haul!

Super OPE Member

It's the chain...

It's the chain...

I'm Dominick

Muh fingers look really big

Here For The Long Haul!

It's the chain...

Super OPE Member

Mastermind Approved!

Here For The Long Haul!

Super OPE Member

Super OPE Member

Mastermind Approved!

Super OPE Member

Similar threads