Best Buy Co, Inc. Buy Used Saws CCC Ebay Store HLSupply Daily Deals Lumber Liquidators
ECHO Bearcat Products Husqvarna OEM Parts EBay Daily Deals

MustangMike's Recent Activity

  1. MustangMike liked cease232's post in the thread What are you building with your milled wood?.

    [IMG][IMG][IMG] Alder dining table. Sent from my iPhone using Tapatalk Pro

    Jun 19, 2018 at 5:33 PM
  2. MustangMike liked cease232's post in the thread What are you building with your milled wood?.

    [IMG][IMG] Knotty alder bathroom vanity with concrete countertop. Sent from my iPhone using Tapatalk Pro

    Jun 19, 2018 at 5:33 PM
  3. MustangMike liked Deets066's post in the thread Received My Asian Big Bore Triplets Today.

    You could trim the intake side skirt of the piston instead of trying to grind the intake port. Similiar affect

    Jun 19, 2018 at 5:28 PM
  4. MustangMike liked huskihl's post in the thread Received My Asian Big Bore Triplets Today.

    Looks like a brake handle bushing for the recoil side. Hard to tell

    Jun 19, 2018 at 5:27 PM
  5. MustangMike liked Leafy's post in the thread Anyone directly compared the new 462 to the new 572 yet?.

    I should have said cheap too. Well need to wait for the am version of the crank to come out I think since the only one I can find is on...

    Jun 19, 2018 at 5:25 PM
  6. MustangMike liked Bigmac's post in the thread 461 starting problems.

    So what did you do differently that’s making it start better for you now? I like the stock coil, unless you are limbing with it a ton, I...

    Jun 19, 2018 at 4:19 PM
  7. MustangMike replied to the thread Received My Asian Big Bore Triplets Today.

    That makes sense! Any idea on that other thing???

    Jun 19, 2018 at 4:18 PM
  8. MustangMike liked huskihl's post in the thread Received My Asian Big Bore Triplets Today.

    That pin might be a brake band retainer pin

    Jun 19, 2018 at 4:17 PM
  9. MustangMike liked AlfA01's post in the thread Received My Asian Big Bore Triplets Today.

    Looks like you got some hogging to do. That AM intake looks a bit narrower too, or is it just the angle of the pic?

    Jun 19, 2018 at 4:17 PM
  10. MustangMike attached a file to the thread Received My Asian Big Bore Triplets Today.

    Here are pics of the jugs and misc parts. Measuring the intake opening from the base, it is 21/32 on the D jug, and 13/16 on the Big...

    IMG_20180619_153929321_HDR.jpg IMG_20180619_153939198_HDR.jpg Jun 19, 2018 at 4:01 PM
  11. MustangMike replied to the thread Received My Asian Big Bore Triplets Today.

    I think if I can lower the intake on the Big Bore jugs, that is the easiest way to get decent performance, but I'm just guessing at this...

    Jun 19, 2018 at 3:56 PM
  12. MustangMike liked AlfA01's post in the thread Received My Asian Big Bore Triplets Today.

    Dang, .058 w/o a base gasket? Bravo Hutzl. So, after getting a good look at these on the saw, what's your heading for dealing with them?

    Jun 19, 2018 at 3:54 PM
  13. MustangMike replied to the thread Received My Asian Big Bore Triplets Today.

    I'll take a pic of it next to the D jug when I take the pic of the other parts. Based on my measurements, and knowing the D jug was 74,...

    Jun 19, 2018 at 3:54 PM
  14. MustangMike liked Stihl Potlicker's post in the thread 461 starting problems.

    it seems to be starting fine now, with or without decomp in. i should probably put an 046 or 066 coil on her next

    Jun 19, 2018 at 3:53 PM
  15. MustangMike liked Stihl Potlicker's post in the thread 461 starting problems.

    Yes, but you have to pay attention as i found out with the 880:( i thought i had the tab lined up went to pull it out, but broke it in...

    Jun 19, 2018 at 3:53 PM
Best Buy Co, Inc. GeekBuying.com
TireBuyer.com