High Quality Chainsaw Bars Husqvarna Toys

Recent content by illmakeufamous

  1. I

    McCulloch Super Air Steam IV Blower carb

    Anyone know where I can find a replacement carb for one of these? Sent from my iPhone using Tapatalk
  2. I

    Another 2001 Murray Mid Engine Mower Question

    Thanks guys. I’ve got another one on the way Sent from my iPhone using Tapatalk
  3. I

    Another 2001 Murray Mid Engine Mower Question

    I thought it was worn but the Wear indentions are so uniform all the way around it had me second guessing myself Sent from my iPhone using Tapatalk
  4. I

    Another 2001 Murray Mid Engine Mower Question

    That’s the idler pully. The engine pully is metal and appears to be in good condition Sent from my iPhone using Tapatalk
  5. I

    Another 2001 Murray Mid Engine Mower Question

    And fish, I couldn’t find a place for a fifth mounting bolt Sent from my iPhone using Tapatalk
  6. I

    Another 2001 Murray Mid Engine Mower Question

    Here it is. Thoughts? Sent from my iPhone using Tapatalk
  7. I

    Another 2001 Murray Mid Engine Mower Question

    Ok just checked the pulleys. It felt like the idler pulley 690410MA wasn’t smooth on the surface where the belt rides, possible belt wearing divot in to the pulley over time causing less tension? Sent from my iPhone using Tapatalk
  8. I

    Another 2001 Murray Mid Engine Mower Question

    I’ll look again for more bolts when I get a chance but #62 is all I noticed Sent from my iPhone using Tapatalk
  9. I

    Another 2001 Murray Mid Engine Mower Question

    Low gears are fine, it’s the higher gears and I’ve already took all the slack out of the clutch pedal rod (I know I’m not talking technical terms here. I’ll check the pulley and spring. The spring has me suspect because I noticed when I took it off to replace the drive belt that the holes the...
  10. I

    Another 2001 Murray Mid Engine Mower Question

    My mower is slipping in 4th and 5th gear, especially going up hill. I can see the belt is moving. If I put it in 1-3rd it’ll catch and go up hill no problem. If I sit there long enough the belt will eventually catch and it will go uphill in the higher gears but the belt will start to burn before...
  11. I

    2001 Murray mid engine mower carb question

    Here’s the best I could get. Sorry for the delayed response. It has stamp on in saint Nikki 694080 Sent from my iPhone using Tapatalk
  12. I

    2001 Murray mid engine mower carb question

    This is what I came up with: 280702-0111-01 but that isn’t correct because I ordered a carb rebuild kit from that parts diagram and not even the bowl gasket fit. The stamp on the motor is ridiculously faint. The mower is 309005x51A. 2001, sorry not 2004. And yes, gas did get in with the oil...
  13. I

    2001 Murray mid engine mower carb question

    I have a mid engine mower with a Nikki carb #694080. It was spewing gas from the exhaust. I pulled it last night and cleaned what I could but aside from the float needle and the idle screw, I didn’t see anything that I could replace with a rebuild kit and I can’t find a new carb for it. Is there...
  14. I

    What is yer perfession?

    Social work field, with people with developmental and intellectual disabilities. Sent from my 831C using Tapatalk
  15. I

    MM Husqvarna 435

    Has anyone ever modded their husky 435 muffler? I'm thinking about doing it with mine but wanted to see if anyone here has done it so see if there were noticeable difference. Sent from my 831C using Tapatalk
See more
Top