High Quality Chainsaw Bars Husqvarna Toys

288xp milling

WoodsliverDan

Mechanical Beaver Builder
Local time
4:49 PM
User ID
6878
Joined
Jul 30, 2018
Messages
210
Reaction score
315
Location
Michigan
I have a 288xp I would like to use for milling. My current dilemma is rather I should just use 36" bar with it, which won't max out my 36" Alaskan. Or if the saw would be able to run a 42" bar which would allow me to use the full 36" of mill. I am worried I will be asking too much of the saw.. I have a tip oiler so oil issue my concerns. Thanks.
 

WoodsliverDan

Mechanical Beaver Builder
Local time
4:49 PM
User ID
6878
Joined
Jul 30, 2018
Messages
210
Reaction score
315
Location
Michigan
I've heard of a low of low profile chains breaking when used for milling. Sounds like a waste of money.
 

Lightning Performance

Here For The Long Haul!
Local time
4:49 PM
User ID
677
Joined
Jan 26, 2016
Messages
10,991
Reaction score
28,050
Location
East of Philly
I've heard of a low of low profile chains breaking when used for milling. Sounds like a waste of money.
Everyone I hear of breaking LP was not using Stihl chain. Did I hear wrong?

We shall see. I can only run it on a 28" right now. The bar needs some clean up and a proper built 050 tip on a worn down nose sprocket. Keeping oil on the bar is a problem. Best can be done till the GB comes back around. Considered trying it on a 36"ES WN. It would need and add on oil supply on my 3003 mount.
 

srcarr52

Shop rat, backyard slice cutter.
GoldMember
Local time
4:49 PM
User ID
522
Joined
Jan 12, 2016
Messages
3,920
Reaction score
25,886
Location
Iowa City
Country flag
Everyone I hear of breaking LP was not using Stihl chain. Did I hear wrong?

We shall see. I can only run it on a 28" right now. The bar needs some clean up and a proper built 050 tip on a worn down nose sprocket. Keeping oil on the bar is a problem. Best can be done till the GB comes back around. Considered trying it on a 36"ES WN. It would need and add on oil supply on my 3003 mount.

You're correct there, it was carlton.

I know Logosol is using Stihl LP RM chain, I was going to try some but never had a chance.

Yes, I was cutting 31" of wet red oak with a ported 395 running an 8 pin. It was hauling (for chainsaw milling) until the third cut when I snapped the chain.

I had an external drip oilier on the tip, running a 36" Oregon 50 gauge bar, filed tip to spear the 3/8 LP correctly, .404x8 rim cut down to fit the LP chain and the bar has been belt sanded to make it thinner for the narrow kerf of the LP chain.
 

Lightning Performance

Here For The Long Haul!
Local time
4:49 PM
User ID
677
Joined
Jan 26, 2016
Messages
10,991
Reaction score
28,050
Location
East of Philly
It is a lot of work to get the bar right. Don't forget to tell them you only get to use about two thirds of the chain cutter.

Edit:
Steam might have helped break that chain. Fast chain makes heat in wet wood. It gets me on hot days. Bites down on the used up chains. Big live fresh cut maple and willow stumps are the worst!
 

WoodsliverDan

Mechanical Beaver Builder
Local time
4:49 PM
User ID
6878
Joined
Jul 30, 2018
Messages
210
Reaction score
315
Location
Michigan
Hmm, interesting. Even though slightly off topic. Good info, none the less.
 

JB-PlantHeirloom

Super OPE Member
Local time
4:49 PM
User ID
7856
Joined
Nov 13, 2018
Messages
302
Reaction score
428
Location
Georgia
Country flag
FWIW: I run the low profile ripping chain from Baileys 3/8 x .050 32" on a Husqvarna 385 for milling and have had no problems, except it can be slow when in oak. I have run the same setup ripping firewood with my 288, and have had no problems.

The chain runs much smoother and most importantly cooler then full profile and/or regular full comp chain, as I have tried all three. I have not tried chisel /square chain.
 
Top